Setting up A Bathtub
Setting up A Bathtub
Blog Article
The article author is making a few good points related to A Step-by-Step Guide to Installing a Bathtub overall in the article which follows.
Installing a bathtub isn't precisely rocket science, yet it does require strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably difficult job. If the old tub is easily easily accessible, the task can move rapidly; if you need to open a wall surface to get rid of the old tub and place the new tub, the job is much harder. In either case, the job is within a residence handyman's abilities, although you will certainly need a helper to leave the old bathtub and also embeded in the brand-new one. Make sure you have qualified yourself for the task and are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed project, it is better to think about utilizing one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This post will assist you install a new tub in your restroom if you have actually currently acquired a brand-new tub and don't require to change the arrangement of your previous water supply pipes.
Your tools and material list should comprise the following:
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you ought to do is detach the supply of water. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing taps can be fairly bothersome as a result of the limited gain access to that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth all set for the staying water that will originate from the pipes. Once the supply pipes have actually been eliminated, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Prior to moving on to fit the brand-new taps, contrast the pipe connections on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require reducing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin guaranteeing that the washers are in area in between the faucet and the sink. Safeguard the faucet in place with the manufacturer offered backnut. As soon as the tap is securely in position, the supply pipes can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous type must be attached to the faucet ends first, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Utilizing the two wooden boards under its feet, place the bathtub in the needed position. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four small factors.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the tub up until the level reads level.
To set up taps, fit the bottom of the furthest flexible tap port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Activate the supply of water and also check all joints and also brand-new pipework for leakages and also tighten them if essential. Load the bath tub and also check the overflow electrical outlet and also the regular electrical outlet for leakages.
Finally, repair the bathroom paneling as explained in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait till the bathtub has been utilized a minimum of when as this will settle it right into its final setting.
Getting ready for the Installation
To start with, the supporting framework provided with the bathroom needs to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to make certain that if the tap features a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps device to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of both taps utilizing 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you make use of every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to now prepare to be suited its last placement.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to crack a stiff seal, triggering the water to penetrate the wall surface in between the bath and the tiling, causing difficulties with moisture and also possible leaks to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures and also installations. They are marketed in tubes as well as cartridges, as well as can sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to permit the movement experienced when the bathtub remains in use. The sealer can crack rather early if you do not take into consideration this activity before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the market. It is a good idea to fit the tiles utilizing waterproof or waterproof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen person who reads on A Step-by-Step Guide to Installing a Bathtub, I assumed sharing that piece of content was beneficial. Loved our blog posting? Please share it. Let other people check it out. I value reading our article about How to Install a Bathtub.
About
Report this page